Solar Power for Domestic IT


For this post I’m returning to a subject that I covered previously and one that always fascinates me. Though this time I will go into a little more detail.

A 100 Watt System for Essential Electronics

The idea of going off-grid to provide some, or all, of our energy needs has never been more appealing. With the cost of energy soaring and the possibility of events or circumstances leading to a complete loss of supply, it is now a good idea to learn how one may be able to maintain essential communications and IT needs if the worst should happen!

Communications and IT are really the only essential aspects of our modern lives (in most everyday situations) that absolutely require a supply of electricity … obviously. Many will know how to cope with a loss of power and make alternative arrangements for many other things such as cooking, lighting and heating etc. Particularly those of us who are familiar with out-doors pursuits or lucky enough to live in a home with basic combustion heating – solid fuel stoves and boilers. However, these are matters out-side of the scope of my article which is specifically focusing on essential electrical needs.

The thought of a loss of access to electrical power is quite unsettling for anyone that needs to use the web and IT resources on a daily basis, though there are easy off-grid solutions available! In fact, providing electrical power to keep all essential domestic IT systems and devices up-and-running doesn’t require much in terms of solar / battery infrastructure. Though a word of warning, it does require some degree of technical (electrical) competence and modest electrical construction skills; Some of my proposed set up will also require a small application of soldering skills.

Main Components

solar panel

100 Watt, 12 Volt rigid solar panel – these are relatively cheap at this time and can even be found in the 2nd hand market.

charge controller

Charge controller – is essential for intelligently regulating the battery charging process. It goes between the solar panel and battery.

battery

12 Volt 100 A/h AGM (Absorbent Glass Mat) battery. These are quite affordable and a better alternative to the old-fashioned flooded lead-acid battery. AGM batteries have good performance and a long life span, though they don’t pack as much punch as Lithium batteries. A lithium battery with a similar capacity would cost almost four times as much though! If you are on a very low budget then a bog-standard flooded lead acid car battery could also be used.

It is always preferable to use deep cycle “leisure” batteries in a solar power system as these can withstand and recover from high levels of depletion.

raspi

Raspberry Pi (or similar) SBC (Single Board Computer) . These devices are a real boon for low energy and off-grid users. They provide very useful and powerful general computing capability with a tiny power requirement and are much more energy efficient than any laptop or desktop.

router

Router – a standard router should work fine in this system

monitor

Low energy LED monitor – any size should be fine. However, a direct mains powered monitor will not be suitable. Instead we need to use one that has a 12 Volt or 19 Volt DC input – most modern monitors will meet this requirement.


A simple diagram of my system

Solar system

System Voltages

Our IT electrical system is required to provide three main voltages … these are sometimes referred to as “rails” by engineers. We need 12 Volts at approx 8 Amps. The 12 Volt rail is the main “power rail” in our system as this is the voltage coming out of the battery. 12 Volts is required for directly powering our monitor and router / modem. The later is one of the most energy hungry items and should only be powered-on when required.

buck converter

Buck Converter

Next we need the all-important 5 Volt rail which will be provided by little buck converters adjusted to output 5 V from the main 12V input. 5 volts is required to power our Raspberry Pi computer and provide the 5 V power for the USB charging socket(s) for mobiles and tablets. The Raspberry Pi 4B computer requires around 3A and we need about 1.5A for general charging. The output voltage is adjusted with the little brass screw.

boost converter

19V Boost Converter

Lastly, we need a 19 V rail provided by a Boost Converter (from the 12 V DC input) – this voltage is only required for charging or powering Laptops.

On a good sunny day this system will be running well within capacity, with lots of head-room when running a Raspi 4, Router, 24in low energy LED monitor and charging a laptop simultaneously.

Essential Calibration & Measurements

meter

Cheap Volt Meter

Monitoring voltages is more important (initially) than current consumption. You will need either a multimeter or a cheap panel mounting Volt meter ranging from 0 to 20 Volts. You must use a meter that will clearly read 5V 12V and 19V such as the one shown. I believe it is better to use old passive (analogue) meters rather than state-of-the-art digital multimeters or stand-alone digital meters as these require their own batteries or additional power rails. The objective with off-gridding is to keep auxiliary power use and consumables to a minimum. The meter will be used to set and periodically check the output of the DC/DC voltage converters plus the battery on and off load voltage.

It is very important to make sure that the voltage converters are correctly adjusted, as a mistake could result in a lot of 5 Volt equipment being burnt out! When working with multiple voltage systems, such as this, I like to stick to the ATX colour coding scheme commonly used in all IT hardware with yellow for +12V, Red for +5V and black for 0V or ground. If running a power system which provides other higher voltages such as 19 V it is a good idea to indicate this with some other colour such as Brown or Violet for +19V. Note that in the ATX system Orange is designated for 3.3 V and Blue for -12V (with respect so ground) so don’t use those colours. I would always make sure that only red wires are used for +5V on the output of the system board! I don’t want to accidentally connect my Raspberry Pi or Iphone charge port to a 12 or 19 V power rail!

Don’t Use Inverters

An Inverter is a complex, quite inefficient, and often very expensive device that is used to convert 12 or 24V DC from a battery to 240V AC 50Hz. Some people use these in solar battery systems to provide a mains voltage output which they then use to charge or run a laptop through the standard AC to DC converter or power brick. This is very wasteful, instead it is better to power these devices directly from the DC system, as with our example, using the 19V boost converter.

power plug

Generally, it is a good idea to have peripherals that run on low voltages, as most external devices do. If your monitor is an old fashioned type with a mains input on a “kettle lead” then it is not suitable for a solar battery system. Most modern LED monitors will run on 12 or 19V DC and would be powered through a mains voltage converter or power brick. DC power is then usually fed into the monitor through a barrel jack. Your router will also have a similar powering arrangement and again it should be operating on 12V though some will require 9v DC inputs. In that case you would only need to adjust your buck converter for a 9V output.

A good solar system should be low voltage and DC throughout. Very old fashioned components such as first gen modems that require low voltage AC can not be run on this system.

How Much Does it Cost?

It varies – by far the battery will usually be the most expensive single component. However, as I mentioned above, this setup will work very well with a standard car battery, even an old one from a scrap dealer could provide many useful hours of service.

A new 12 V 100 A/h AGM battery is typically £170.00

The charge controller is £17.00

Buck converters £3.00 each

12 to 19 V Boost converter £14.00

12 Volt 100 Watt solar panel – around £80 to £120

Raspberry Pi computer £50.00

Meter £11.00

General other bits and bobs £10.00

The overall cost will depend on how professional you want to make your energy panel look. Personally, I prefer to use professional connectors and enclosures and these can add a fair amount to the cost.

Otherwise just mount everything on a piece of wood and use bog-standard terminal blocks, stripped USB cables and other sundry items for the output interface. You could use 5Amp round pin (lamp) plugs for your main 12V and 5V outputs for monitor / router & raspi respectively.

USB charging ports should be made up from circuit board mounted USB plugs soldered to strip board — this requires some electronics construction skill.

Footnote

Obviously this article is really just scratching the surface and is based on a proposed but not yet constructed system. I am writing from the perspective of someone that is quite comfortable with electronic construction, soldering, technical improvisation, Ohms Law, connectivity standards in IT and the making up of special purpose leads. Much of this article will be skimming the surface of the obvious for anyone with similar skills but for those who are new to the wonderful world of electronics and solar power then I hope it will give some added impetus to your desire to further investigate the subject.


«   |  


Category: Technology   Tags:

03-Feb-2022


prestbury web

Prestburyweb

Set up in 2016 by Oliver Wood, Prestburyweb provides support in all aspects of web based media to business & organisations across the UK.

Contact



© 2022   Presweb Wordpress theme by Oliver Wood